Firmware and Technical Support Details
While the EZABL will work with almost any printer that runs open-source firmware (Marlin, Rep-Rap, Klipper, etc), our technical support for firmware assistance covers the printers on the supported list below with their stock control boards or EZBoard (on supported models) when running our Unified Firmware package. We also provide support for Klipper and have a guide here: EZABL Klipper Setup Guide.
Most touchscreen models are NOT supported due to their limited, closed-source firmware.
*Our support covers the EZABL probe setup. You must make sure the rest of your Klipper setup is completed and working.
Supported Model List
- ADIMLab Gantry i3
- Alfawise U10
- Anet A2
- Anet A6
- Anet A8
- Anet A8 Plus
- Anet E10
- Anet E12
- Anet E16
- AnyCubic Chiron – (Needs LCD kit)
- AnyCubic Mega Zero V1
- AnyCubic Mega Zero V2
- Artillery AL-4
- Artillery Sidewinder X1
- Creality CR-10
- Creality CR-10 Mini
- Creality CR-10 S4
- Creality CR-10 S5
- Creality CR-10S
- Creality CR-10S Mini
- Creality CR-10S S4
- Creality CR-10S S5
- Creality CR-10 V2
- Creality CR-10 V3
- Creality CR-10S Pro V1- (Needs LCD kit)
- Creality CR-10S Pro V2 – (Needs LCD kit)
- Creality CRX – (Needs LCD kit)
- Creality Ender 2
- Creality Ender 2 Pro
- Creality Ender 3/3 Pro
- Creality Ender 3 MAX
- Creality Ender 3 MAX NEO (LCD Kit recommended, works with stock LCD)
- Creality Ender 3 NEO (LCD Kit recommended, works with stock LCD)
- Creality Ender 3 S1 – (LCD Kit recommended, works with stock LCD)
- Creality Ender 3 S1 Plus – (Needs LCD Kit)
- Creality Ender 3 S1 Pro – (Needs LCD Kit)
- Creality Ender 3 V2 – (LCD Kit recommended, works with stock LCD)
- Creality Ender 3 V2 NEO – (LCD Kit recommended, works with stock LCD)
- Creality Ender 4
- Creality Ender 5/5 Pro
- Creality Ender 5 Plus – (Needs LCD kit) – If you want to not have to cut your stock Z endstop wire add on the Ender 5 Plus/Ender 6 Endstop Cable on the EZABL Page.
- Creality Ender 6 – (Needs LCD kit) – If you want to not have to cut your stock Z endstop wire add on the Ender 5 Plus/Ender 6 Endstop Cable on the EZABL Page.
- Creality Ender 7 – (Needs LCD Kit)
- Entina Tina 2
- Geeetech A10 V1/A10 V2
- Geeetech A20
- JGMaker JGMaker Magic
- Kingroon KP3
- Kingroon KP3S
- Monoprice Cadet
- Monoprice Maker Select
- PowerSpec I3 Mini V1
- PowerSpec I3 Mini V2
- Sovol SV01
- Sovol SV01 Pro
- Sovol SV03
- Sovol SV06
Sovol SV06 Plus
- Sunlu S8
- Tevo Tornado
- Tevo Tarantula Pro
- Voxelab Aquila X1 – (LCD Kit recommended, works with stock LCD)
- Wanhao Duplicator i3 (and rebrands)
- Wanhao Duplicator i3 Mini (and rebrands)
- Zyltech Gear V1/V2/V3 – Needs EZABL Z Cable in addition to the kit
Other Printers
- Setting up EZABL on Vanilla Marlin or Duet?. The EZABL works like a normally open endstop switch and will physically work with boards running Marlin or RepRap (Duet) but the included support does not cover getting your custom machine setup but support on a custom machine is available at an hourly rate. Otherwise, you can always check out our communities for getting the EZABL working on a non-supported board/printer here: Community.TH3DStudio.com
