/**
 * For directions on how to use this firmware visit http://uf2.th3dstudio.com and click on your printer/board link
 * NO IMPLIED SUPPORT OR WARRANTY IS PROVIDED WITH THIS FIRMWARE AND IS PROVIDED AS-IS
 *
 * MAKE SURE ALL SLICERS AND OTHER PROGRAMS THAT CONNECT TO YOUR PRINTER COM PORT ARE CLOSED BEFORE FLASHING.
 */
#pragma once
#define CONFIGURATION_H_VERSION 02010200

#define UNIFIED_VERSION "TH3D UFW 2.88"
#define STRING_DISTRIBUTION_DATE "2024-07-23"

//===========================================================================
//============================ TH3D Configuration ===========================
//===========================================================================

// ONLY UNCOMMENT ONE PRINTER AT A TIME!!! IF YOU HAVE MULTIPLE MACHINES FLASH THEM ONE AT A TIME.
// UNCOMMENT MEANS REMOVING THE // IN FRONT OF A #define XXXXXX LINE.

// PRINTER NOTE: Works with the wifi and non-wifi models as well as the Monoprice Cadet rebrand. The stock ABL sensor is enabled by default.
// NOTE: This firmware ONLY works without the wifi module. If you have the wifi module, disconnect it from your board before flashing.

//===========================================================================
// ****************   TINA2/CADET PRINTERS 2560 CPU BOARD   *****************
//===========================================================================
//#define TINA2
//#define CADET

// V3 Setting - If you have the "mushroom" type endstops uncomment this line to set the V3 hardware settings
//#define V3_HARDWARE

// EZABL Probe Mounts - Uncomment the mount you are using for your EZABL to enable EZABL support in the firmware.
//#define TINA2_OEM     //for the stock 12mm probe mount included on the printer
//#define CUSTOM_PROBE

// Z Homing Option - Use EZABL or stock ABL sensor to home Z instead of endstops
//#define USE_EZABL_HOMEZ

// Z Probe Alternate Wiring - If you want to use the Z MAX endstop port to connect your EZABL instead of the HALL header, uncomment the below line
// This will also enable the USE_EZABL_HOMEZ option for homing.
//#define TINA2_EZABL_ZMAX

//===========================================================================
// *************************  END PRINTER SECTION   *************************
//===========================================================================

/**
 * EZABL Advanced Settings - EZABL_POINTS & EZABL_PROBE_EDGE are also used for other probes
 */

// Probing Grid Points - If you want more or less EZABL probe points change the number below, use odd numbers. Total points is # times #.
#define EZABL_POINTS 3

// Probe Edge - How far from the edge of the bed to probe from. Use 30 if using binder clips. This also sets the edge inset value for MANUAL_MESH_LEVELING.
#define EZABL_PROBE_EDGE 10

// Fast Probing - Works with most machines and all EZABL sensors (8mm/s)
#define EZABL_FASTPROBE

// Superfast Probing - Only works with the EZABL Pro Sensors (15mm/s)
//#define EZABL_SUPERFASTPROBE

// Heaters on During Probing - Heaters will stay on during probing - May reduce accuracy do not use unless told to by support
//#define HEATERS_ON_DURING_PROBING

// Probing Steppers Off - This will cycle the XYE stepper motors during probing to reduce interference from them. When using this do NOT touch the X or Y during probing as they will not be locked.
//#define PROBING_STEPPERS_OFF

// Slow Down Moves - Does your machine make weird noises/vibrations when it is probing the mesh? Enable this to slow down the speed between probe points.
//#define SLOWER_PROBE_MOVES

// Grid Extrapolation - This will use the mesh data to make assumptions of the bed outside the probe area. Disable if you are getting incorrect results on the edges of the bed.
#define EXTRAPOLATE_BEYOND_GRID

/**
 * BLTouch/CRTouch
 * 
 * If you want to use the BLTouch/CRTouch uncomment the BLTOUCH line below.
 * You also need then enter in your sensor offsets below in the CUSTOM PROBE section.
 * 
 * If you need to change your SERVO pin you can change that with the SERVO0_PIN Line below. Most people do NOT need to change/set this.
 */
//#define BLTOUCH
//#define SERVO0_PIN 11

/**
 * Custom Probe Offset - EZABL/BLTouch/CRTouch
 * 
 * If you have a probe mount that is not pre-setup in the firmware then uncomment
 * the CUSTOM_PROBE option (or BLTOUCH if using one) above and enter your probe offsets below
 */
#if ANY(CUSTOM_PROBE, BLTOUCH)
  /**
  * Z Probe to nozzle (X,Y) offset, relative to (0, 0).
  *
  * In the following example the X and Y offsets are both positive:
  *
  *   #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
  *
  *     +-- BACK ---+
  *     |           |
  *   L |    (+) P  | R <-- probe (10,10)
  *   E |           | I
  *   F | (-) N (+) | G <-- nozzle (0,0)
  *   T |           | H
  *     |    (-)    | T
  *     |           |
  *     O-- FRONT --+
  *   (0,0)
  *
  * Specify a Probe position as { X, Y, Z }
  * Do NOT enter an number for the Z position in here. Store your offset in EEPROM.
  * 
  * When is the offset POSITIVE?
  * If the probe is right of the nozzle the offset on X is POSITIVE
  * If the probe is behind of the nozzle the offset on Y is POSITIVE
  * 
  * When is the offset NEGATIVE?
  * If the probe is left of the nozzle the offset on X is NEGATIVE
  * If the probe is in front of the nozzle the offset on Y is NEGATIVE
  */
  #define NOZZLE_TO_PROBE_OFFSET { 10, 10, 0 }
#endif


//===========================================================================
//******************** Extra Features and Tweaks ****************************
//===========================================================================

// EXTRUDER SETTINGS -------------------------------
// Use to set custom esteps and/or reverse your E Motor direction if you are installing an extruder that needs the direction reversed.
// If you reversed the wiring on your E motor already (like the Bondtech Guide says to do) then you do not need to reverse it in the firmware here.
//
// Example EStep Values For Common Extuders: 
// TH3D Aluminum Extruder ---  95 ESteps
// LGX/LGX Lite/NG Extruder - 400 ESteps
// TH3D Tough Extruder V2 --- 407 ESteps
// TH3D Tough Extruder V1 --- 410 ESteps
// Bondtech BMG Extruder ---- 415 ESteps
// Creality Sprite Extruder - 425 ESteps
// LDO Orbiter/Sherpa Mini -- 690 ESteps
//
// If you want to change the Esteps for your printer you can uncomment the below line and set CUSTOM_ESTEPS_VALUE to what you want - USE WHOLE NUMBERS ONLY
// This option sets the esteps from the CUSTOM_ESTEPS_VALUE line below.
// If you need to reverse the e motor direction also enabled the REVERSE_E_MOTOR_DIRECTION option.
//#define CUSTOM_ESTEPS
#define CUSTOM_ESTEPS_VALUE 410
//#define REVERSE_E_MOTOR_DIRECTION

// FILAMENT SENSOR UNLOAD SETTINGS -----------------
// If you have a filament sensor that is physically mounted to the machine you can enable MOUNTED_FILAMENT_SENSOR to set the unload length to 5mm to prevent filament from backing up in the sensor by uncommenting MOUNTED_FILAMENT_SENSOR 
//#define MOUNTED_FILAMENT_SENSOR

// If you have a direct drive machine with a filament sensor uncomment DIRECT_DRIVE_PRINTER to decrease the unload length from 100mm to 20mm
//#define DIRECT_DRIVE_PRINTER

// THERMISTOR SETTINGS -----------------------------

// If you are using an E3D V6 Hotend (or Hemera) with their cartridge thermistor (not glass version) uncomment the below line.
//#define V6_HOTEND

// If you are using a Tough Hotend from TH3D or any thermistors TH3D sells for your hotend uncomment the below line.
//#define TH3D_HOTEND_THERMISTOR

// If you are using a known hotend thermistor value uncomment the below 2 lines and enter the thermistor number replacing the X after the #define KNOWN_HOTEND_THERMISTOR_VALUE
//#define KNOWN_HOTEND_THERMISTOR
//#define KNOWN_HOTEND_THERMISTOR_VALUE X

// If you have a hotend and thermistor capable of over 290C you can set the max temp value below.
// Setting this higher than 290C on a stock or traditional thermistor will damage it. Refer to your thermistor documentation to see what max temp is.
//#define HIGH_TEMP_THERMISTOR
#define HIGH_TEMP_THERMISTOR_TEMP 350

// BED THERMISTOR SETTINGS -------------------------

// If you are using a thermistor TH3D sells for your bed uncomment the below line.
//#define TH3D_BED_THERMISTOR

// If you are using a Keenovo with SSR and the Keenovo temperature sensor uncomment the below line.
//#define KEENOVO_TEMPSENSOR

// If you are using a known bed thermistor value uncomment the below 2 lines and enter the thermistor number replacing the X after the #define KNOWN_BED_THERMISTOR_VALUE
//#define KNOWN_BED_THERMISTOR
//#define KNOWN_BED_THERMISTOR_VALUE X

// If you are using an AC bed with a standalone controller (Keenovo) uncomment the below line to disable the heated bed in the firmware
//#define AC_BED

// MISC --------------------------------------------

// LCD Knob Direction
// Turning your LCD knob clockwise should move DOWN in the menus/make values increase and counter-clockwise should move UP in the menus/make values decrease
// If yours is behaving opposite then enable the REVERSE_KNOB_DIRECTION option below
//#define REVERSE_KNOB_DIRECTION

// If you have a 5015 fan that whines when under 100% speed uncomment the below line.
//#define FAN_FIX

// Use your own printer name - Uncomment both lines
//#define CUSTOM_PRINTER_NAME
//#define USER_PRINTER_NAME "CHANGE ME"

// If your printer is homing to the endstops hard uncomment this to change the homing speed/divisor to make it less aggressive.
//#define SLOWER_HOMING

//===========================================================================
//*************************** Advanced Features *****************************
//===========================================================================

/**
 * EEPROM on SD Card
 * 
 * NOTE: THIS TAKES UP EXTRA SPACE ON THE CPU SO IF YOUR COMPILE FAILS DISABLE SOME OTHER OPTIONS IN THE FIRMWARE.
 * If your board has issues saving the EEPROM that could be due to a defective EEPROM chip. This will make an EEPROM.DAT file
 * You can use a SD card in the printer slot to save the EEPROM to that instead. Just uncomment the below line
 * and then leave an SD card in the printer at all times. If you have to take it out, power off the printer before removing
 * then put your GCode files on the SD card, insert the card again, and then power the printer up.
 */
//#define SDCARD_EEPROM_EMULATION

/**
 * Input Shaping
 * 
 * See here on how to use Input Shaping: https://www.th3dstudio.com/marlin-input-shaping-calculator/
 * 
 * CPU LIMITATION WARNING: While this will compile and fit in memory, these 8-bit CPUs are outdated and may run poorly with input shaping.
 * If you want to reliably and smoothly run input shaping you should upgrade to a 32-bit board. If you have issues, disable input shaping.
 * 
 * Below are the frequency and damping settings for each axis.
 * Damping must have f at the end of the number and the range is 0.00-1.00.
 */
//#define INPUT_SHAPING

// X Axis Settings
#define INPUT_SHAPING_FREQ_X 40
#define INPUT_SHAPING_DAMPING_X 0.15f
// Y Axis Settings
#define INPUT_SHAPING_FREQ_Y 40
#define INPUT_SHAPING_DAMPING_Y 0.15f

/**
 * Bed and Z Height Adjustments
 * 
 * If you need to make changes to your X, Y, and/or Z size on your printer for whatever reason you can uncomment the custom size/height line
 * for whatever axis you need to make changes to and then replace the XXX with the new size in millimeters.
 */
//#define CUSTOM_X_BED_SIZE XXX
//#define CUSTOM_Y_BED_SIZE XXX
//#define CUSTOM_Z_HEIGHT XXX

/**
 * Home Offset Adjustment
 * 
 * If you need to adjust your XY home offsets from defaults then you can uncomment the HOME_ADJUST line below and enter your
 * custom XY offsets. This is provided for convenience and is unsupported with included product support.
 * 
 * How to use - measure (home XY then jog using the LCD 1mm at a time) the X and Y distance the nozzle is off
 * the build plate and then put those as NEGATIVE values below on the X_HOME_LOCATION and Y_HOME_LOCATION values
 * Positive values will NOT work (move your endstops to fix a positive offset or change your bed size above).
 */
//#define HOME_ADJUST
#define X_HOME_LOCATION -10
#define Y_HOME_LOCATION -10

/**
 * PID Bed Temperature Control
 * 
 * If you want PID Bed Temperature control enable the below line. You will need to tune it for your machine.
 * See the PID Bed setup guide here: https://support.th3dstudio.com/helpcenter/p-i-d-bed-calibration-guide/
 */
//#define ENABLE_PIDBED

/**
 * Fine Babystepping
 * 
 * Enabling the below line will set the babystep resolution from 0.025mm to 0.010mm for finer control.
 */
//#define FINE_BABYSTEPPING

/**
 * Linear Advance
 * 
 * See here on how to use Linear Advance: http://marlinfw.org/docs/features/lin_advance.html
 * 
 * Change the K Value with the LINEAR_ADVANCE_K line below or use M900 KX.XX in your starting code (recommended).
 */
//#define LINEAR_ADVANCE
#define LINEAR_ADVANCE_K 0

/**
 * Manual Mesh Leveling 
 *
 * If you want to use manual mesh leveling you can enable the below option. 
 * This is for generating a MANUAL mesh WITHOUT a probe. To change the mesh inset value change the EZABL_PROBE_EDGE setting above.
 * 
 * Mesh Bed Leveling Documentation: http://marlinfw.org/docs/gcode/G029-mbl.html 
 * 
 * NOTE: If you want to automate the leveling process our EZABL kits do this for you. Check them out here: http://EZABL.TH3DStudio.com
 */
//#define MANUAL_MESH_LEVELING

/**
 * Bed Skew Compensation
 *
 * This feature corrects for misalignment in the XYZ axes.
 *
 * Take the following steps to get the bed skew in the XY plane:
 *  1. Print a test square (e.g., https://www.thingiverse.com/thing:2563185)
 *  2. For XY_DIAG_AC measure the diagonal A to C
 *  3. For XY_DIAG_BD measure the diagonal B to D
 *  4. For XY_SIDE_AD measure the edge A to D
 *
 * Marlin automatically computes skew factors from these measurements.
 * Skew factors may also be computed and set manually:
 *
 *  - Compute AB     : SQRT(2*AC*AC+2*BD*BD-4*AD*AD)/2
 *  - XY_SKEW_FACTOR : TAN(PI/2-ACOS((AC*AC-AB*AB-AD*AD)/(2*AB*AD)))
 *
 * If desired, follow the same procedure for XZ and YZ.
 * Use these diagrams for reference:
 *
 *    Y                     Z                     Z
 *    ^     B-------C       ^     B-------C       ^     B-------C
 *    |    /       /        |    /       /        |    /       /
 *    |   /       /         |   /       /         |   /       /
 *    |  A-------D          |  A-------D          |  A-------D
 *    +-------------->X     +-------------->X     +-------------->Y
 *     XY_SKEW_FACTOR        XZ_SKEW_FACTOR        YZ_SKEW_FACTOR
 */
//#define SKEW_CORRECTION

#if ENABLED(SKEW_CORRECTION)
  // Input all length measurements here:
  #define XY_DIAG_AC 282.8427124746
  #define XY_DIAG_BD 282.8427124746
  #define XY_SIDE_AD 200

  // Or, set the XY skew factor directly:
  //#define XY_SKEW_FACTOR 0.0

  //#define SKEW_CORRECTION_FOR_Z
  #if ENABLED(SKEW_CORRECTION_FOR_Z)
    #define XZ_DIAG_AC 282.8427124746
    #define XZ_DIAG_BD 282.8427124746
    #define YZ_DIAG_AC 282.8427124746
    #define YZ_DIAG_BD 282.8427124746
    #define YZ_SIDE_AD 200

    // Or, set the Z skew factors directly:
    //#define XZ_SKEW_FACTOR 0.0
    //#define YZ_SKEW_FACTOR 0.0
  #endif

  // Enable this option for M852 to set skew at runtime
  //#define SKEW_CORRECTION_GCODE
#endif

/**
 * Power Loss Recovery
 * 
 * Continue after Power-Loss feature will store the current state to the SD Card at the start of each layer
 * during SD printing. If this is found at bootup it will ask you if you want to resume the print.
 * NOTE: This feature causes excessive wear on your SD card. This feature is not supported by TH3D Support.
 */
//#define POWER_LOSS_RECOVERY

/**
 * ARC Support Override
 *
 * Arc support is enabled by default on all builds but this takes up extra space.
 * If you get compile errors due to the size being too large when enabling other options, then disable ARC_SUPPORT
 * by uncommenting the DISABLE_ARC_SUPPORT line below.
 */ 
//#define DISABLE_ARC_SUPPORT

/**
 * SD Support Override
 * 
 * If you need to free up flash and ram space to enable more features you can disable the SD card slot on the board.
 * Only do this if you are only printing to the printer over USB from something like Octoprint/EZPi or your PC.
 */
//#define NO_SDCARD

//===========================================================================
// **********************  END CONFIGURATION SETTINGS   *********************
//===========================================================================

/**
 * ****************************DO NOT TOUCH ANYTHING BELOW THIS COMMENT**************************
 * Core machine settings are below. Do NOT modify these unless you understand what you are doing.
 */

//BLTouch/CRTouch ABL Updates
#if ENABLED(BLTOUCH) && DISABLED(CUSTOM_PROBE)
  #define CUSTOM_PROBE
#endif

/**
 * Machine Configuration Settings
 */
 
// Enable Software PWM to avoid Timer Conflict
#define FAN_SOFT_PWM
#if DISABLED(FAN_FIX)
  #define SOFT_PWM_SCALE 0
#endif

//Enable the stock ABL sensor
#if DISABLED(TINA2_OEM)
  #if DISABLED(CUSTOM_PRINTER_NAME)
    #define CUSTOM_PRINTER_NAME
    #if ENABLED(CADET)
      #define USER_PRINTER_NAME "TH3D Cadet"
    #else
      #define USER_PRINTER_NAME "TH3D Tina2"
    #endif
  #endif
  #define TINA2_OEM
#endif

//Cadet uses same settings, difference is the printer name shown
#if ENABLED(CADET)
  #define TINA2
#endif

//Enabled EZABL Home Z when using ZMAX
#if ENABLED(TINA2_EZABL_ZMAX)
  #define USE_EZABL_HOMEZ
#endif

// Tina2 Printer Settings
#if ENABLED(TINA2)
  #define SERIAL_PORT 0
  #define SPACE_SAVER_2560

  #define BAUDRATE 250000
  
  #define MINIPANEL
  #define DEFAULT_LCD_CONTRAST 255
    
  #if ENABLED(REVERSE_KNOB_DIRECTION)
    #define REVERSE_ENCODER_DIRECTION
  #endif

  #ifndef MOTHERBOARD
    #define MOTHERBOARD BOARD_WEEDO_62A
  #endif

  #if ENABLED(CUSTOM_ESTEPS)
    #define DEFAULT_AXIS_STEPS_PER_UNIT   { 100, 100, 400, CUSTOM_ESTEPS_VALUE }
  #else
    #define DEFAULT_AXIS_STEPS_PER_UNIT   { 100, 100, 400, 95 }
  #endif

  #define EXTRUDERS 1

  #if ENABLED(V3_HARDWARE)
    #define X_BED_SIZE 105
  #else
    #define X_BED_SIZE 100
  #endif
  
  #define Y_BED_SIZE 120
  #define Z_MAX_POS 100
  
  #if ENABLED(HOME_ADJUST)
    #define X_MIN_POS X_HOME_LOCATION
    #define Y_MIN_POS Y_HOME_LOCATION
  #else
    #define X_MIN_POS 0
    #define Y_MIN_POS 0
  #endif

  #define USE_XMAX_PLUG
  #define USE_YMIN_PLUG
  #define USE_ZMIN_PLUG
  #if DISABLED(USE_EZABL_HOMEZ)
    #define USE_ZMAX_PLUG
  #endif

  #define X_HOME_DIR 1
  #define Y_HOME_DIR -1
  #if ENABLED(USE_EZABL_HOMEZ)
    #define Z_HOME_DIR -1
  #else
    #define Z_HOME_DIR 1
  #endif
  
  #if NONE(V6_HOTEND, TH3D_HOTEND_THERMISTOR, KNOWN_HOTEND_THERMISTOR)
    #define TEMP_SENSOR_0 1
  #else
    #if ENABLED(EZBOARD_PT100)
      #define TEMP_SENSOR_0 20
    #elif ENABLED(V6_HOTEND)
      #define TEMP_SENSOR_0 5
    #elif ENABLED(KNOWN_HOTEND_THERMISTOR)
      #define TEMP_SENSOR_0 KNOWN_HOTEND_THERMISTOR_VALUE
    #elif ENABLED(TH3D_HOTEND_THERMISTOR)
      #define TEMP_SENSOR_0 1
    #endif
  #endif
  
  #define TEMP_SENSOR_1 0 
  #define TEMP_SENSOR_2 0
  #define TEMP_SENSOR_3 0
  #define TEMP_SENSOR_4 0
  #define TEMP_SENSOR_5 0
  #define TEMP_SENSOR_6 0
  #define TEMP_SENSOR_7 0
  
  #define TEMP_SENSOR_BED 0
  
  #define TEMP_SENSOR_PROBE 0
  #define TEMP_SENSOR_CHAMBER 0

  #define ENDSTOPPULLUPS

  #define X_MIN_ENDSTOP_INVERTING false
  #define Y_MIN_ENDSTOP_INVERTING true
  #define Z_MIN_ENDSTOP_INVERTING true
  #define I_MIN_ENDSTOP_INVERTING false
  #define J_MIN_ENDSTOP_INVERTING false
  #define K_MIN_ENDSTOP_INVERTING false
  #define X_MAX_ENDSTOP_INVERTING false
  #define Y_MAX_ENDSTOP_INVERTING false
  #define Z_MAX_ENDSTOP_INVERTING false
  #define I_MAX_ENDSTOP_INVERTING false
  #define J_MAX_ENDSTOP_INVERTING false
  #define K_MAX_ENDSTOP_INVERTING false
  #define Z_MIN_PROBE_ENDSTOP_INVERTING true
  #if ENABLED(USE_EZABL_HOMEZ)
    #define USE_PROBE_FOR_Z_HOMING
  #endif
  #define Z_MIN_PROBE_USES_Z_MIN_ENDSTOP_PIN

  #define X_DRIVER_TYPE A4988
  #define Y_DRIVER_TYPE A4988
  #define Z_DRIVER_TYPE A4988
  #define E0_DRIVER_TYPE A4988

  #define X_ENABLE_ON 0
  #define Y_ENABLE_ON 0
  #define Z_ENABLE_ON 0
  #define E_ENABLE_ON 0

  #define INVERT_X_DIR false
  #define INVERT_Y_DIR true
  #define INVERT_Z_DIR false
  #define INVERT_E0_DIR true
  
  #define INVERT_E1_DIR false
  #define INVERT_E2_DIR false
  #define INVERT_E3_DIR false
  #define INVERT_E4_DIR false
  #define INVERT_E5_DIR false
  #define INVERT_E6_DIR false
  #define INVERT_E7_DIR false

  #define ENCODER_PULSES_PER_STEP 4
  #define ENCODER_STEPS_PER_MENU_ITEM 1

  //#define FILAMENT_RUNOUT_SENSOR

  #if ENABLED(FILAMENT_RUNOUT_SENSOR)
    #define FIL_RUNOUT_ENABLED_DEFAULT true // Enable the sensor on startup. Override with M412 followed by M500.
    #define NUM_RUNOUT_SENSORS   1          // Number of sensors, up to one per extruder. Define a FIL_RUNOUT#_PIN for each.
    #define FIL_RUNOUT_STATE     HIGH       // Pin state indicating that filament is NOT present.
    #define FIL_RUNOUT_PULLUP               // Use internal pullup for filament runout pins.
    //#define FIL_RUNOUT_PULLDOWN           // Use internal pulldown for filament runout pins.
    #define FIL_RUNOUT_PIN       2          // Chiron sensor on Pin 2 (X+)

    // Set one or more commands to execute on filament runout.
    // (After 'M412 H' Marlin will ask the host to handle the process.)
    #define FILAMENT_RUNOUT_SCRIPT "M600"

    // After a runout is detected, continue printing this length of filament
    // before executing the runout script. Useful for a sensor at the end of
    // a feed tube. Requires 4 bytes SRAM per sensor, plus 4 bytes overhead.
    //#define FILAMENT_RUNOUT_DISTANCE_MM 25

    #ifdef FILAMENT_RUNOUT_DISTANCE_MM
      // Enable this option to use an encoder disc that toggles the runout pin
      // as the filament moves. (Be sure to set FILAMENT_RUNOUT_DISTANCE_MM
      // large enough to avoid false positives.)
      //#define FILAMENT_MOTION_SENSOR
    #endif
  #endif

#endif
// End Tina2 Printer Settings 

/*
 * All other settings are stored in the Configuration_backend.h and Configuration_speed.h files. Do not change unless you know what you are doing.
 */
 
#include "Configuration_backend.h"
#include "Configuration_speed.h"